Operating procedures for automatic vacuum profiled film press
2022-07-18
1、 Before operating the machine, the automatic vacuum profiled film pressing machine must be checked before the shift, and the operation can be started after ensuring that there is no error. During the operation of the machine, operators must operate the machine, inspect the machine, and deal with the problem immediately.
2、 Sufficient space must be reserved around the machine of the automatic vacuum profiled film pressing machine. No miscellaneous work should be piled up beside the machine to avoid affecting the operation of * * and evacuating personnel in case of accidents. When the equipment is in normal use, all guard plates of the equipment must be installed on the machine.
3、 When operating with silicone rubber sheet, it is necessary to preheat first, and it is not allowed to start the program without heating, so as to avoid damaging the silicone plate.
4、 In case of any abnormality in the operation of the automatic vacuum profiled film press, the emergency stop switch should be pressed immediately to stop the working procedure and check and remove the fault. 5、 In case of sudden power failure or accident, you should cut off the power supply and air source before leaving. You have to do anything to leave without permission.
6、 In the process of working, if the automatic vacuum profiled film pressing machine fails under the condition of hydraulic pressure and air flushing, the power supply shall be cut off immediately and the inspection shall be carried out. First, the transfer switch shall be turned to the manual state, and the pressure relief button shall be pressed. If the air is released, the workbench descending button shall be pressed. If the fault can not be found, the professional maintenance personnel shall be informed immediately for treatment, and the air in the warehouse can be released by adjusting the valve if necessary.
7、 It is not allowed to operate this equipment in single shift, especially in night shift.
8、 Before operating the full-automatic vacuum film pressing machine, the operator must undergo necessary professional training and be familiar with the equipment before operation.
9、 The automatic vacuum film pressing machine must be operated no matter what the reasons are. It is not allowed to put the hand or head between the upper and lower cavities for inspection and operation without the introduction. To avoid personal injury caused by sudden start-up of the machine.
10、 The temperature of the heating chamber of the automatic vacuum film pressing machine is about 100 ° C when it is working. It is necessary to avoid direct skin contact to avoid scalding.
11、 If the balance part, hydraulic pipeline and hydraulic cylinder need to be overhauled in case of abnormal equipment during the working process, the worktable must be lifted to * * closed to ensure that the hydraulic pressure does not leak, the power supply is cut off and someone is protected. Reliable objects (generally square timber or Jack) are padded between the pallet and the support plate of the hydraulic cylinder. Single person is not allowed to carry out this operation on site.
12、 Before operating the equipment, it is necessary to read the operation manual carefully to understand its performance and correct operation method.
13、 A reliable grounding device must be connected before the equipment is connected to the power supply.
14、 The power line of the equipment must be connected to the power supply with protection switch, and check whether the voltage and frequency of the power supply are appropriate.
15、 Before operating the equipment, it is necessary to confirm whether the running direction of the oil pump is correct, otherwise, the wiring position of the power phase line must be changed. 16、 Before operating the equipment, check whether the * * protective devices are normal and whether the components are loose or damaged. Otherwise, timely adjust and replace them to ensure their normal functions. And remember to remove the adjustment tools.
17、 When operating the automatic vacuum film pressing machine, you must wear tight clothes. It is strictly forbidden to wear loose clothes or tie, watch and bracelet. Those who have long hair should wear working cap to cover their long hair.
18、 When the equipment of automatic vacuum profiled film pressing machine is running, all protective devices cannot be dismantled or opened without authorization.
19、 When the equipment is in operation, it is strictly forbidden for the operator to leave the work post.
20、 It is forbidden to process workpieces beyond the original design function of the machine tool and use accessories beyond the design function of the equipment.
21、 It is strictly forbidden to operate automatic vacuum film pressing machine in poor health or after drinking.
22、 Before inspecting, repairing and cleaning the equipment, the main power supply of the automatic vacuum film pressing machine must be cut off.
23、 After the operation of the machine tool, the main power supply must be cut off, and the machine can not leave until it stops running completely.
24、 In order to prevent the possibility of misoperation of the automatic vacuum film pressing machine, the operator shall not allow any part of his body to enter into the pressing area of the equipment no matter under any circumstances.
25、 Do a good job of equipment maintenance every day, fill in the equipment maintenance record; completely disconnect the automatic vacuum film pressing machine before off duty. Machine tool air source power switch can be left.
2、 Sufficient space must be reserved around the machine of the automatic vacuum profiled film pressing machine. No miscellaneous work should be piled up beside the machine to avoid affecting the operation of * * and evacuating personnel in case of accidents. When the equipment is in normal use, all guard plates of the equipment must be installed on the machine.
3、 When operating with silicone rubber sheet, it is necessary to preheat first, and it is not allowed to start the program without heating, so as to avoid damaging the silicone plate.
4、 In case of any abnormality in the operation of the automatic vacuum profiled film press, the emergency stop switch should be pressed immediately to stop the working procedure and check and remove the fault. 5、 In case of sudden power failure or accident, you should cut off the power supply and air source before leaving. You have to do anything to leave without permission.
6、 In the process of working, if the automatic vacuum profiled film pressing machine fails under the condition of hydraulic pressure and air flushing, the power supply shall be cut off immediately and the inspection shall be carried out. First, the transfer switch shall be turned to the manual state, and the pressure relief button shall be pressed. If the air is released, the workbench descending button shall be pressed. If the fault can not be found, the professional maintenance personnel shall be informed immediately for treatment, and the air in the warehouse can be released by adjusting the valve if necessary.
7、 It is not allowed to operate this equipment in single shift, especially in night shift.
8、 Before operating the full-automatic vacuum film pressing machine, the operator must undergo necessary professional training and be familiar with the equipment before operation.
9、 The automatic vacuum film pressing machine must be operated no matter what the reasons are. It is not allowed to put the hand or head between the upper and lower cavities for inspection and operation without the introduction. To avoid personal injury caused by sudden start-up of the machine.
10、 The temperature of the heating chamber of the automatic vacuum film pressing machine is about 100 ° C when it is working. It is necessary to avoid direct skin contact to avoid scalding.
11、 If the balance part, hydraulic pipeline and hydraulic cylinder need to be overhauled in case of abnormal equipment during the working process, the worktable must be lifted to * * closed to ensure that the hydraulic pressure does not leak, the power supply is cut off and someone is protected. Reliable objects (generally square timber or Jack) are padded between the pallet and the support plate of the hydraulic cylinder. Single person is not allowed to carry out this operation on site.
12、 Before operating the equipment, it is necessary to read the operation manual carefully to understand its performance and correct operation method.
13、 A reliable grounding device must be connected before the equipment is connected to the power supply.
14、 The power line of the equipment must be connected to the power supply with protection switch, and check whether the voltage and frequency of the power supply are appropriate.
15、 Before operating the equipment, it is necessary to confirm whether the running direction of the oil pump is correct, otherwise, the wiring position of the power phase line must be changed. 16、 Before operating the equipment, check whether the * * protective devices are normal and whether the components are loose or damaged. Otherwise, timely adjust and replace them to ensure their normal functions. And remember to remove the adjustment tools.
17、 When operating the automatic vacuum film pressing machine, you must wear tight clothes. It is strictly forbidden to wear loose clothes or tie, watch and bracelet. Those who have long hair should wear working cap to cover their long hair.
18、 When the equipment of automatic vacuum profiled film pressing machine is running, all protective devices cannot be dismantled or opened without authorization.
19、 When the equipment is in operation, it is strictly forbidden for the operator to leave the work post.
20、 It is forbidden to process workpieces beyond the original design function of the machine tool and use accessories beyond the design function of the equipment.
21、 It is strictly forbidden to operate automatic vacuum film pressing machine in poor health or after drinking.
22、 Before inspecting, repairing and cleaning the equipment, the main power supply of the automatic vacuum film pressing machine must be cut off.
23、 After the operation of the machine tool, the main power supply must be cut off, and the machine can not leave until it stops running completely.
24、 In order to prevent the possibility of misoperation of the automatic vacuum film pressing machine, the operator shall not allow any part of his body to enter into the pressing area of the equipment no matter under any circumstances.
25、 Do a good job of equipment maintenance every day, fill in the equipment maintenance record; completely disconnect the automatic vacuum film pressing machine before off duty. Machine tool air source power switch can be left.
